Cisco Systems EDFA2 Manuel d'opérations Page 176
- Page / 280
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
FINAL DRAFT - CISCO CONFIDENTIAL
9-28
Cisco ONS 15216 EDFA2 Operations Guide
78-16033-01
Chapter 9 TL1 Commands
TL1 Commands and Autonomous Messages
9.7.20 REPT ALM EQPT
Command REPT ALM EQPT
Reports when a general alarm (not directly affecting optical signal or power bus) is logged or cleared
(derived from cerent15216EdfaAlarmState).
Syntax
<sid> <date> <time>
<almcde> <atag> REPT ALM EQPT
"<aid>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"
;
Example 9-22 REPT ALM EQPT Message
Amp01 2001-06-18 14:48:44
* 141 REPT ALM EQPT
"EQPT:MN,LCRNT1,NSA,6-18,14-48-44,,:\"Excessive Pump1 Current\""
;
ntfncde Notification code (maps to cerent15216EdfaAlarmPriority).
Possible values are:
CR Critical alarm.
MJ Major alarm.
MN Minor alarm.
CL Cleared alarm.
NA No alarm.
ocrdat m-d Date (month-day) of the event occurrence (derived from
cerent15216EdfaDateAndTimeString).
ocrtm h-m-s Time (hour-minute-second) of the event occurrence (derived
from cerent15216EdfaDateAndTimeString).
sid string Source identifier uniquely identifies the source of a TL1
autonomous command.
time hh:mm:ss Time of origination of TL1 message.
Table 9-26 REPT ALM ENV Syntax Description (continued)
Parameter Syntax Description
- Cisco ONS 15216 EDFA2 1
- Operations Guide 1
- CONTENTS 3
- 6 ASH Commands 6-1 5
- 7 FTP Command Line 7-1 7
- 8 Provisioning Using TL1 8-1 7
- 9 TL1 Commands 9-1 8
- 10 Troubleshooting 1 9
- Contents 10
- 78-16033-01 10
- Obtaining Documentation 19
- Documentation Feedback 20
- Cisco.com 20
- Technical Assistance Center 21
- Applications 23
- 1.3 Key Features 24
- 1.3.1 Constant Gain 25
- 1.3.2 Gain Flattening 25
- 1.3.3 Transient Suppression 26
- 1.3.4 Low Noise 26
- 1.3.5 SNMP MIBs 26
- 1.3.6 TL1 26
- Technical Specifications 27
- 2.1.1 Maximum Input Power 28
- 2.1.2 Channel Loading 28
- °C end of life 29
- 2.4 External Features 30
- 2.5 Front Panel 31
- Front Panel 32
- Installation 33
- Chapter 3 Installation 34
- 3.4 SC/UPC Optical Ports 35
- SC/UPC Optical Ports 36
- 3.5 Communications 37
- 3.5.2 Alarm LEDs 38
- 3.5.2.3 LOS LED (Yellow) 39
- 3.5.2.4 Ethernet Socket LEDs 39
- 3.5.3.1 Required Equipment 39
- Communications 40
- Remote Site 43
- Local Site 43
- 3.5.4.2 Modem Signals 44
- 3.5.4.3 Modem Power Up 44
- Table 3-6 Modem Settings 45
- GND RXD TXD 46
- 4.2 Set IP Address 51
- 4.4 Set Date and Time 52
- 4.7 Set Gain 53
- 4.8 Set Alarm Thresholds 53
- °C. Valid entries 56
- °C. Valid 57
- °C. Valid entries are 57
- °C. Setting this value to 57
- 4.9 Set Password 58
- 4.10 Add Users 59
- 4.11 Save Changes 59
- 4.12 Log Off 60
- Step 3 Save the changes 61
- 5.1 SNMP Overview 63
- 5.1.2.1 SNMP Agent 64
- 5.1.2.2 SNMP MIB 65
- 5.1.2.3 SNMP Manager 65
- • Creating a View, page 5-6 67
- 5.2.1 Creating a View 68
- 5.2.2.1 Set CommunityEntry 69
- 5.3 Setup for CTM Access 72
- 5.4 Tables and Groups 73
- 5.4.1 CfgGroup Table 74
- Tables and Groups 75
- 5.4.2 PumpCfgEntry Table 76
- 5.4.4 OverallControl Table 80
- 5.4.5 PumpStatusEntry Table 80
- 5.4.6 AlarmEntry Table 81
- 5.4.7 OpGroup Table 82
- 5.5 Setting Up Traps 83
- 5.5.1 Display Trap Command 84
- 5.5.2 Set Trap Command 85
- 5.5.3 Set Agent Trap Enable 85
- 5.6 Retrieving Information 86
- 5.6.2 Date and Time 87
- and set the local 87
- 5.6.3 Power Gain 88
- 5.6.4 Case Temperature 89
- 5.6.4.2.2 CtmpMax 90
- 5.6.4.3.1 CtmpMaxHysteresis 90
- 5.6.5 Power Bus 91
- 5.6.6 Input Power (Signal) 92
- 5.6.7 Output Power 93
- 5.6.7.1.2 OutPowerdBm 94
- 5.6.7.2.1 LpoutSetpoint 94
- 5.6.7.2.2 LpoutDeviation 95
- Retrieving Information 97
- 5.6.9 Alarm Entry 98
- 5.7 Summary of SNMP Alarms 99
- Summary of SNMP Alarms 100
- ASH Commands 101
- Chapter 6 ASH Commands 102
- 6.2 Configuration Commands 106
- 6.3 Administrative Commands 110
- 6.3.1 clear Command 111
- 6.3.2 exit Command 111
- 6.3.3 help Command 111
- 6.3.4 history Command 111
- 6.4 Shell Commands 112
- 6.5.1 ffs file list Command 114
- 6.6 SNMP Commands 115
- Command snmp attribute list 116
- 6.6.5 snmp mib get Command 118
- 6.6.6 snmp mib list Command 118
- 6.6.8 snmp row get Command 120
- 6.6.9 snmp row set Command 120
- Command snmp subtree list 122
- 6.7 User Commands 125
- 6.9 Restore Commands 131
- 6.10 Manufacturer Mode 132
- FTP Command Line 133
- 7.2 FTP Commands 135
- FTP Commands 136
- Provisioning Using TL1 137
- 8.2 Set IP Address 139
- 8.4 Set Date and Time 140
- 8.7 Set Gain 141
- 8.8 Set Alarm Thresholds 141
- CISCO ONS 15216 142
- ALARM OUT 142
- Set Alarm Thresholds 144
- 8.9 Set Password 146
- 8.10 Add Users 147
- 8.11 Log Off 147
- TL1 Commands 149
- 9.4 Notation 150
- Chapter 9 TL1 Commands 151
- 9.7.1 ACT-USER 157
- 9.7.2 ALW-MSG-ALL 157
- 9.7.3 APPLY 159
- 9.7.4 CANC-USER 160
- 9.7.5 COPY-RFILE 160
- 9.7.6 CPY-MEM 162
- 9.7.7 DLT-RFILE 163
- 9.7.8 DLT-USER-SECU 164
- 9.7.9 ED-DAT 164
- 9.7.10 ED-DWDM 165
- 9.7.11 ED-ENV 166
- 9.7.12 ED-NE-GEN 167
- 9.7.13 ED-PID 168
- 9.7.14 ED-USER-SECU 169
- 9.7.15 ENT-USER-SECU 169
- 9.7.16 INH-MSG-ALL 170
- 9.7.17 INIT-SYS 173
- 9.7.18 REPT ALM DWDM 173
- 9.7.19 REPT ALM ENV 175
- 9.7.20 REPT ALM EQPT 176
- 9.7.22 REPT EVT FXFR 180
- 9.7.23 RTRV-ALM-ALL 181
- 9.7.24 RTRV-ALM-DWDM 183
- 9.7.25 RTRV-ALM-ENV 185
- 9.7.26 RTRV-ALM-EQPT 186
- 9.7.27 RTRV-AO 188
- 9.7.28 RTRV-COND-ALL 189
- 9.7.29 RTRV-COND-DWDM 191
- 9.7.30 RTRV-COND-ENV 192
- 9.7.31 RTRV-COND-EQPT 194
- 9.7.32 RTRV-DFLT-SECU 195
- 9.7.33 RTRV-DWDM 196
- 9.7.34 RTRV-ENV 198
- 9.7.35 RTRV-HDR 199
- 9.7.36 RTRV-INV 199
- 9.7.37 RTRV-NE-GEN 200
- 9.7.38 RTRV-RFILE 202
- 9.7.39 RTRV-TH-DWDM 203
- 9.7.40 RTRV-TH-ENV 204
- 9.7.41 RTRV-TH-EQPT 205
- 9.7.42 RTRV-TOD 207
- 9.7.43 RTRV-USER-SECU 208
- 9.7.44 SET-ATTR-SECUDFLT 208
- 9.7.45 SET-TH-DWDM 209
- 9.7.46 SET-TH-ENV 210
- 9.7.47 SET-TH-EQPT 211
- 9.7.48 STA-LOCL-RST 212
- Troubleshooting 213
- 10.1 Alarm Indicators 214
- 10.1.1.2 FAIL LED (Red) 215
- 10.1.1.3 LOS LED (Yellow) 215
- 10.1.2 Optical Alarms 216
- Alarm Indicators 217
- 10.1.3 Equipment Alarms 218
- 10.1.4 Environmental Alarms 219
- 10.2.4 Boot Up Failure 220
- 10.2.8 Lost Password 222
- Regulatory Compliance 225
- Translated Safety Warnings 226
- Warning Definition 228
- DC Power Supply Warning 230
- Installation Warning 231
- Power Cord Warning 231
- No On/Off Switch Warning 232
- SELV Circuit Warning 233
- Laser Radiation Warning 234
- Laser Beam Warning 235
- Power Cabling Warning 235
- Grounded Equipment Warning 236
- Ground Connection Warning 237
- Jewelry Removal Warning 238
- Qualified Personnel Warning 239
- Supply Circuit Warning 239
- Power Supply Wiring Warning 240
- Incorrect Connection Warning 242
- Ground Conductor Warning 243
- More Than One Power Supply 245
- Exposed DC Power Wire Warning 246
- 48 VDC Power System 247
- Chassis Power Connection 248
- Product Disposal Warning 252
- Energy Hazard 253
- Ground Wire Warning 256
- Class B EMC Warning 259
- Safety Requirements Warning 259
- Optical Connector Warning 262
- Eye Damage Warning 263
- Static Electricity Warning 264
- Connector Cleaning Warning 265
- Module Removal Warning 267
- Reinforced Insulation Warning 269
- Power Supply Voltage Warning 270
- Avvertenza 271
- Advarsel 271
- ¡Advertencia! 271
- Varning! 271
Produits connexes et manuels pour Mise en réseau Cisco Systems EDFA2
(22 pages)
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels