Cisco Systems IOS XR Manuel d'utilisateur Page 76
- Page / 282
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Implementing BGP on Cisco IOS XR Software
How to Implement BGP on Cisco IOS XR Software
RC-60
Cisco IOS XR Routing Configuration Guide
Configuring a Route Reflector for BGP
Perform this task to configure a route reflector for BGP.
All the neighbors configured with the route-reflector-client command are members of the client group,
and the remaining iBGP peers are members of the nonclient group for the local route reflector.
Together, a route reflector and its clients form a cluster. A cluster of clients usually has a single route
reflector. In such instances, the cluster is identified by the software as the router ID of the route reflector.
To increase redundancy and avoid a single point of failure in the network, a cluster can have more than
one route reflector. If it does, all route reflectors in the cluster must be configured with the same 4-byte
cluster ID so that a route reflector can recognize updates from route reflectors in the same cluster. The
/jointfilesconvert/86220/bgp cluster-id command is used to configure the cluster ID when the cluster has more than one route
reflector.
SUMMARY STEPS
1. configure
2. router /jointfilesconvert/86220/bgp autonomous-system-number
3. /jointfilesconvert/86220/bgp cluster-id cluster-id
4. neighbor ip-address
5. remote-as autonomous-system-number
6. address-family {ipv4 unicast | ipv4 multicast | ipv6 unicast | ipv6 multicast}
7. route-reflector-client
8. end
or
commit
DETAILED STEPS
Command or Action Purpose
Step 1
configure
Example:
RP/0/RP0/CPU0:router# configure
Enters global configuration mode.
Step 2
router /jointfilesconvert/86220/bgp
autonomous-system-number
Example:
RP/0/RP0/CPU0:router(config)# router /jointfilesconvert/86220/bgp 120
Enters BGP configuration mode allowing you to configure
the BGP routing process.
Step 3
/jointfilesconvert/86220/bgp cluster-id
cluster-id
Example:
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp)# /jointfilesconvert/86220/bgp
cluster-id 192.168.70.1
Configures the local router as one of the route reflectors
serving the cluster. It is configured with the cluster ID of
192.168.70.1 to identify the cluster.
- Text Part Number: OL-5554-05 1
- CONTENTS 3
- Contents 10
- Preface 11
- Obtaining Documentation 12
- Documentation Feedback 13
- Submitting a Service Request 15
- BGP Functional Overview 18
- BGP Router Identifier 19
- BGP Default Limits 19
- BGP Configuration 20
- Neighbor Submode 21
- Configuration Templates 22
- Template Inheritance Rules 23
- Template Inheritance 27
- No Default Address Family 31
- Routing Policy Enforcement 32
- Update Groups 34
- BGP Best Path Algorithm 34
- Comparing Pairs of Paths 35
- Order of Comparisons 36
- Multiprotocol BGP 37
- Route Dampening 39
- BGP Route Reflectors 40
- Enabling BGP Routing 44
- Logging Neighbor Changes 50
- Adjusting BGP Timers 50
- Configuring BGP Weights 54
- Configuring a BGP Neighbor 74
- Disabling a BGP Neighbor 85
- Monitoring BGP Update Groups 91
- BGP Confederation: Example 94
- IS-IS Functional Overview 101
- IS-IS Configuration Grouping 101
- IS-IS Interfaces 102
- Multitopology Configuration 102
- Limit LSP Flooding 102
- Single-Topology IPv6 Support 103
- Nonstop Forwarding 104
- Multitopology IPv6 Support 104
- Multi-Instance IS-IS 105
- Overload Bit on Router 105
- Default Routes 106
- Multicast-Intact Feature 106
- Prerequisites 107
- DETAILED STEPS 108
- Restrictions 109
- SUMMARY STEPS 110
- Example: 113
- Example:: 117
- Prerequisite 126
- Summary Steps 134
- Customizing Routes for IS-IS 135
- Software 138
- Where to Go Next 140
- Additional References 140
- Technical Assistance 141
- OSPF Functional Overview 145
- OSPF Routing Components 148
- Backbone Area 149
- Stub Area 149
- Not-so-Stubby Area (NSSA) 149
- OSPF Process and Router ID 150
- Supported OSPF Network Types 151
- Authentication Strategies 152
- Key Rollover 152
- Default Route for OSPF 153
- Route Redistribution for OSPF 155
- Graceful Restart for OSPFv3 157
- Restart Mode 158
- Enabling OSPF 161
- Examples 180
- address mask 185
- Enabling Graceful Restart 198
- ABR 1 Configuration 207
- ABR 2 Configuration 207
- Cisco IOS XR Software 211
- Overview of RIB 212
- RIB Administrative Distance 213
- RIB Support for IPv4 and IPv6 213
- How to Deploy and Monitor RIB 214
- Routing Policy Language 222
- Named Set Form 224
- Inline Set Form 224
- Named Form 225
- Inline Form 226
- Routing Policy Language Usage 227
- Set community based on MED 228
- Policy Definitions 229
- Parameterization 230
- Boolean Operator Precedence 231
- When Attributes Are Modified 232
- Default Drop Disposition 233
- Control Flow 233
- Policy Verification 234
- Policy Statements 235
- Disposition 236
- Boolean Conditions 238
- Attach Points 239
- BGP Policy Attach Points 240
- Dampening 241
- Default Originate 241
- Neighbor Export 242
- Neighbor Import 242
- Redistribute 243
- Show bgp 244
- Table Policy 245
- BGP Attributes and Operators 245
- OSPF Policy Attach Points 247
- OSPFv3 Policy Attach Points 248
- IS-IS Policy Attach Points 250
- Attached Policy Modification 251
- Defining a Route Policy 253
- policy-name 256
- Directly Connected Routes 265
- Recursive Static Routes 265
- Floating Static Routes 266
- Configuring a Static Route 266
- Configuration Examples 271
Produits connexes et manuels pour Mise en réseau Cisco Systems IOS XR
(144 pages)
(12 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels