Cisco Systems PGW 2200 Guide de l'utilisateur Page 70
- Page / 436
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-56
Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide
OL-18083-01
Chapter 2 Installing the Sun Solaris 10 Operating System
Loading the Sun Solaris 10 Operating System
-------------------------------------------------------------------------------
ESC-2_Continue ESC-6_Help
Note The system takes approximately 30 seconds to process this selection. A countdown appears in the
display after you activate your choice.
Step 15 Ver if y th at No is selected and press ESC-2 to continue.
Text similar to the following is displayed:
- Set the Default Route for /jointfilesconvert/99324/bge0 -----------------------------------------------
To specify the default route, you can let the software try to detect one
upon reboot, you can specify the IP address of the router, or you can choose
None. Choose None if you do not have a router on your subnet.
> To make a selection, use the arrow keys to select your choice and press
Return to mark it [X].
Default Route for /jointfilesconvert/99324/bge0
--------------------------
[ ] Detect one upon reboot
[X] Specify one
[ ] None
-------------------------------------------------------------------------------
ESC-2_Continue ESC-6_Help
Step 16 Ver if y th at Specify one is selected and press ESC-2 to continue.
Text similar to the following is displayed:
- Default Route IP Address for /jointfilesconvert/99324/bge0 --------------------------------------------
Enter the IP address of the default route. This entry will be placed in the
/etc/defaultrouter file and will be the default route after you reboot
(example 129.146.89.225).
Router IP Address for /jointfilesconvert/99324/bge0
-------------------------------------------------------------------------------
ESC_Continue ESC-6_Help
Step 17 Enter the Router IP address of this interface in dotted decimal format and press ESC-2 to continue.
Note See “Solaris 10 Required Media Checklist” in Table 1-2 if you used the checklist to record the
router IP address.
Text similar to the following is displayed:
- Confirm Information for /jointfilesconvert/99324/bge0 -------------------------------------------------
> Confirm the following information. If it is correct, press F2;
to change any information, press F4.
- Text Part Number: OL-18083-01 1
- CONTENTS 3
- Contents 4
- Document Objectives 9
- Audience 9
- Related Documentation 9
- Document Change History 10
- Installation 11
- Required Software Media 12
- Minimum System Requirements 12
- Required Tasks 13
- Table 1-4 Tasks Checklist 14
- Supported Platforms 15
- Supported Disk Drives 15
- Before You Start 16
- - Selecting package (SUNWifp) 20
- Host” section on page 2-50 26
- 89 blocks 34
- 426 blocks 34
- 8 blocks 34
- SUNWnfscr 43
- SUNWkrbr 43
- /devices-/devicesdevfs-no 45
- Configuring Your Host 64
- SUNWnfscr 85
- SUNWnisu 85
- DO NOT REBOOT 100
- OL-18083-01 104
- (CSCOh026) 117
- Using the SunVTS Test Package 145
- Normal Unit Test 145
- Running a Test in Brief Mode 149
- Running a Test in Full Mode 150
- Manager (ILOM) 152
- Figure 2-1 System Agreement 153
- Figure 2-4 LOM Screen 154
- Start ILOM Using Secure HTTP 157
- An Example of Using ILOM 161
- Serial Console ttya 162
- Cautions, Notes, and Tips 166
- Enter y and press Enter 169
- Enabling Sudo 179
- Installing the License File 179
- Software 183
- Software Directory Structure 185
- % MGC_Setup 190
- Configuring Groups and Users 193
- Basic Tasks 196
- Deleting an SNMP COMMUNITY 201
- Adding a Trap Destination 202
- Deleting a Trap Destination 204
- Activating the New Settings 205
- Specifying IP Addresses 212
- Configuring Engine Parameters 214
- Setting the Call Cutoff Timer 216
- Enabling Call Screening 216
- Configuring Switchover 221
- Configuring SCP Queries 224
- Sample trigger.dat File 227
- .odbc.ini File Information 265
- Setting Up Replication 265
- Network Requirements 266
- Synchronizing Databases 270
- Configuring Cisco ITP-Ls 271
- Configuring the Data Dumper 272
- Migrating to Solaris 10 and 275
- Release 9.8 275
- Cautions and Notes 276
- Required Software 277
- License Installation 277
- Recording System Data 277
- Migration Overview 278
- Installing Sun Solaris 10 282
- Restoring Data Files 283
- Platforms 295
- Live Upgrade Procedure 296
- Falling Back Overview 300
- Release 9.5 or 9.6 301
- Backup Procedure 308
- Restoring the System 309
- LAN Switch Overview 311
- Catalyst 2900 XL Series 312
- Catalyst 5500 and 5000 Series 312
- XECfgParm.dat File Parameters 313
- Special Parameters 314
- Relationships 359
- HP OpenView 363
- Formatting Trap Messages 365
- Step 8 Close the window 366
- Sample Installation Scripts 367
- Sample Uninstall Scripts 413
- Sample LAN Configurations 421
Produits connexes et manuels pour Logiciel Cisco Systems PGW 2200
(32 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels