Cisco Systems ISR4451XK9 Manuel d'utilisateur Page 145
- Page / 160
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6-29
Hardware Installation Guide for the Cisco 4451-X Integrated Services Router
OL-27644-01
Chapter 6 Installing and Upgrading Internal Modules and FRUs
Installing and Removing the PVDM4
Step 4 Loosen and remove the three screws on the PVDM4.
Step 5 Lift the PVDM4 up from the motherboard.
Step 6 Place the PVDM4 in an anti-static bag.
Step 7 Replace the cover.
Installing the PVDM4 on the Cisco Fourth-Generation T1/E1 Voice and WAN
NIM in the Cisco ISR 4451-X
Step 1 Shut down the electrical power to the slot in the router by either turning off the electrical power to the
router or by issuing the online insertion and removal (OIR) commands. Leave the power cable plugged
in to channel ESD voltages to ground. For more information on OIR, see the Appendix, “Online
Insertion and Removal (OIR) and Hot-Swapping”.
Step 2 Loosen the two captive screws on the network interface module.
Step 3 Remove the network interface module. (See Figure 6-22.)
Figure 6-22 Network Interface Module with PVDM4
Step 4
Locate the three standoffs on the network interface module where the PVDM4 will reside.
Step 5 Align the PVDM4 with the connector and the standoffs and attach the PVDM4 with the three screws.
Step 6 Slide the network interface module back in the router and tighten the captive screws.
345528
2
3
1
4
1
1 Captive Screws 2 Ports
3 Network Card 4 PVDM4
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 4
- 4 Initial Configuration 4-1 5
- Objectives 9
- Audience 9
- Organization 10
- Conventions 11
- Waarschuwing 12
- Varoitus 12
- Attention 12
- Avvertenza 13
- Advarsel 13
- ¡Advertencia! 13
- Varning! 13
- Related Documentation 17
- Searching for Cisco Documents 18
- About the Cisco ISR 4451-X 19
- Chassis Views 21
- Cisco ISR 4451-X Chassis 22
- Chassis Views 23
- Platform Summary 25
- Labels on Cisco ISR 4451-X 26
- Hardware Features 27
- Front Panel Ethernet Ports 28
- Dual Mode GE/SFP Ports 28
- USB Serial Console Port 28
- Front Panel PoE+ Ports 28
- LED Indicators 29
- Hardware Features 30
- External Slots 31
- Modules and Cards 33
- Power Supplies 34
- About Slots and Interfaces 35
- About Slots and Interfaces 36
- Slot Numbering 37
- Specifications 38
- Specifications 39
- Standard Warning Statements 44
- Standard Warning Statements 45
- Safety Recommendations 48
- Safety Recommendations 49
- General Site Requirements 50
- General Site Requirements 51
- Rack Requirements 52
- Console Port Connections 55
- Auxiliary Port Connections 56
- Ethernet Connections 57
- Installation Checklist 59
- Creating a Site Log 60
- What You Need to Know 63
- Before You Begin 63
- Unpacking the Router 64
- Installing the Router 64
- Rack-Mounting the Chassis 65
- Installing the Router 66
- Mounting the Router in a Rack 67
- Grounding the Chassis 69
- Statement 1032 70
- Chassis Grounding 71
- Connecting Power 72
- Connecting to AC Power 73
- • no parity 75
- • 1 stop bit 75
- • no flow control 75
- Using the Setup.exe program 78
- Statement 1001 80
- Ports and Cabling 82
- Initial Configuration 84
- Completing the Configuration 87
- Default Routes 96
- Default Network 96
- Gateway of Last Resort 96
- Configuration Examples 100
- SUMMARY STEPS 101
- DETAILED STEPS 101
- Prerequisites 102
- Examples 102
- ROM Monitor Overview 107
- Entering ROM Monitor Mode 108
- Environment Variable Settings 111
- Exiting ROM Monitor Mode 113
- Configuration Example 114
- Example of Upgrade 115
- Internal and External Modules 117
- Safety Warnings 118
- OL-27644-01 119
- Safety Warnings 119
- Accessing Internal Modules 120
- Overview 123
- LEDs on the NIM-SSD 124
- • 104°F (40°C) at sea level 125
- Solid State Drives (SSD) 126
- Restrictions 131
- Statement 94 132
- Locating and Orienting DIMM 134
- 1 Polarization notch 135
- Removing a DIMM 136
- Installing a DIMM 137
- Software Requirement for SMs 140
- Locating an SM or NIM 140
- Removing an SM or NIM 140
- Installing an SM 140
- Verifying SM Installation 141
- Statement 1073 144
- Statement 1030 144
- NIM in the Cisco ISR 4451-X 145
- ASR1000-RP1 147
- Replacing a Fan Tray 150
- Replacing a Fan Tray 151
- Installing SFP Modules 154
- Installing SFP Modules 155
- Laser Safety Guidelines 156
- Removing SFP Modules 156
- Statement 1051 157
- Hot-Swapping 159
- OIR Procedures 160
- Hot-Swapping Procedures 160
Produits connexes et manuels pour Passerelles/contrôleurs Cisco Systems ISR4451XK9
(40 pages)
(30 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels